LM Sanyo Semicon Device datasheet pdf data sheet FREE Datasheets ( data sheet) search for integrated circuits (ic), semiconductors and other electronic . LM min typ nax unit. *. mA. mA. mA. MA. mA. *. * Electrical Characteristics at Ta= 25°C,Vss=0V,VOD=-9 to – 15V. Output ‘H’ Level Current. ALARM. LM datasheet, LM pdf, LM data sheet, datasheet, data sheet, pdf, SANYO, Dual – Alarm Digital Clock.

Author: Grogis Dukus
Country: Belarus
Language: English (Spanish)
Genre: Health and Food
Published (Last): 9 February 2016
Pages: 25
PDF File Size: 6.75 Mb
ePub File Size: 3.69 Mb
ISBN: 285-7-40236-995-2
Downloads: 82992
Price: Free* [*Free Regsitration Required]
Uploader: Moogull

This clock regeneration may be carried out externally using a tuned circuit or internally using the on-chip Digital Clock Regenerator. Bender New Member May 26, May just be crazy enough to try, I did not check datashee pincount though. That’s why ,m8363 wondering if your notations are correct. Media New media New comments Search media. I think it should say pulled up to Vdd. Sadly, you may be out of luck.

I found a datasheet for a TMS Previous 1 2 However, what is missing is most likely a slide switch that would have pin “b” as a common point. Or tell me what I need to buy to make it run at 60Hz? By using the status register 2, users can select either of; alarmclock data speed, in the wide range, which is caused by the oscillation circuit ‘s frequency deviationcontroller 1 VDDL Alarm expansion register 1 INT register 1 Clock correction register FOUT.


Hi All Apart from doing some basic electrical work back in high school 13 years ago it would be safe to say that I have lost some skills and require some assistance. So it should work down under without the missing part.

LM datasheet & applicatoin notes – Datasheet Archive

Thread starter Bender Start date May 26, Forums New posts Search forums. I went ahead and checked the pinout.

Battery backup On-chiphour system Power failure indicating function All digits flashing Clock noise suppressor. Potentiometer Questions Started by norbss Yesterday at Valid only when using the alarm functionSupply Voltage Detection Circuit “. Activating VSS using two inputs simultaneously alarm select and sleep selectthe. The switch on the side adjusts the clock radios brightness and also set the time. Hero Banned May 30, So in 50 Hz land common “B” gets connected to “c” which is what you have now without the missing part.

Therefore, a requirement eatasheet using. By continuing to use this site, you are consenting to our use of cookies. Replacing a 4 pin leaded inductor with a 2 pin Started by gkmaia Yesterday at I then purchased lmm8363 step down converter so it would work and it does just fine however the time is out by 10 seconds.

You might not need to disconnect anything, try linking pins B and C and it might work. Yep Datashedt did miss count, I hadn’t had my morning coffee yet I suspect that there may be more missing than one might think if the distributors knew that the clock would only be sold in a area of 60 Hz. On the back of the clock radio there is a place where it looks like a switch should be to allow me to change between 50 and 60 Hz.


I found 2 chips one on the radio and the other just behind the display of the clock. What clock IC does it use?

LM8363 Datasheet PDF – ETC

This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register. Digital Clock Regenerator In order to decode the incoming. Also, for 50Hz, I think you want to tie pin 26 to ground Vssnot power pin. LM with led clock Abstract: In addition, the CDP features an alarm circuit thatby a transparent “freeze” circuit that assures data integrity when accessing the clock.

To participate you need to register. Of coarse, there is japan which is 50hz in the west and 60hz in the east.